Buy Concrete Equipment

In the Air Dryer System (ADS), the air rises through a bed of marbles and into deliquescent/desiccant tablets inside the tank before the air exits the vessel. Approximately 50% of residual moisture is removed (after cooling). Removed moisture is collected in the bottom of the separator tank. An after-filter removes particulates that may have become airborne, then used in the abrasive blasting operation.

Size Options:
250 cfm, 400 cfm, 750 cfm, 950 cfm, 1200 cfm, 1600 cfm, 2000 cfm, 2500 cfm

The operation of the AmphiBlast™ Lite is simple. Set the desired blast pressure using the blast pressure control regulator. Choose to blast dry or wet by pushing or pulling a button on the control panel. During wet abrasive blasting, simply dial the water pressure regulator to the desired flow rate represented by the water over air differential pressure gauge reading.

The AmphiBlast Lite comes in two options, standard with an onboard water tank and without.

The operation of the AmphiBlast™ Mini is simple. Set the desired blast pressure using the blast pressure control regulator. Choose to blast dry or wet by pushing or pulling a button on the control panel. During wet abrasive blasting, simply dial the water pressure regulator to the desired flow rate represented by the water over air differential pressure gauge reading.

The AmphiBlast Mini comes in two options, standard with an onboard water tank and without.

Crushed glass abrasives offer concrete workers an eco-friendly, silica-free solution for surface preparation. It provides precise blasting with minimal dust, improving job site safety and cleanliness. Ideal for removing coatings, rust, and contaminants, crushed glass helps achieve smooth, durable concrete surfaces without excessive wear.

Mesh Size: #10/20, #20/30, #30/60, #40/70, #60/140

Packaging: 63 x 50lb Bags, 3,086lb Bulk Bag, Bulk Per Ton

*Sold by the pallet*

Crushed glass abrasives offer concrete workers an eco-friendly, silica-free solution for surface preparation. It provides precise blasting with minimal dust, improving job site safety and cleanliness. Ideal for removing coatings, rust, and contaminants, crushed glass helps achieve smooth, durable concrete surfaces without excessive wear.

Mesh Size: Extra Fine, Fine, Medium, Medium Fine

Packaging: 56 x 50lb Bags, 3,000lb Bulk Bag, Bulk Per Ton 

*Sold by the pallet*

Van Air Systems' Dry-O-Lite is a low-cost absorbent deliquescent desiccant formulated for single and sequential tower dehydration systems. When used in a properly sized single or sequential tower desiccant air dryer, Dry-O-Lite will remove sufficient moisture vapor to establish a 55% RH in the air line.

Packaging: 50lb bag, 40 x 50lb bag

The Schmidt® M-Series blasters add flexibility to your blasting operation. These multi-media units can be used with a wider range of abrasive media than standard blasters, including sodium bicarbonate, aluminum oxide, plastic, glass beads, crushed glass and even steel grit. Use a single system for all your jobs—from cleaning surface grease and oil, to stripping rust or paint. The M-Series can achieve the surface profile you need because you have the ability to use the abrasive best suited for the job.

Available Options: 0.9 cu.ft, 1.5 cu.ft, 2.0 cu.ft, 3.0 cu.ft

The Schmidt® M-Series blasters add flexibility to your blasting operation. These multi-media units can be used with a wider range of abrasive media than standard blasters, including sodium bicarbonate, aluminum oxide, plastic, glass beads, crushed glass and even steel grit. Use a single system for all your jobs—from cleaning surface grease and oil to stripping rust or paint. The M-Series can achieve the surface profile you need because you have the ability to use the abrasive best suited for the job.

Venturi nozzles are a crucial component in the sandblasting process, designed to maximize efficiency and performance. These nozzles accelerate the flow of abrasive material while minimizing air consumption. As air enters the nozzle, it creates a vacuum that draws in the abrasive, allowing for a powerful and controlled blast.

Our Venturi nozzles are available in various sizes and configurations to suit different applications, ensuring optimal performance for both light and heavy-duty projects. They are crafted from high-quality materials for durability and resistance to wear, making them ideal for a range of surface preparation tasks.